Main Page → Skeleton Tracking → 6 RigidBody Skeleton Markerset
This is needed only for the 6 Rigid Body skeleton markerset.
Let's first start with defining a rigid body for the chest puck. Open up the Trackables pane, make sure the Rigid Bodies option is selected at the bottom, and access the Create tab. This will bring up options for defining rigid bodies in Motive.
In the 3D viewport, select all of the 8 markers on the chest puck, and you should be able to see the selected markers in the Trackables pane. Name the rigid body as Chest, and click create. If you are attaching the active puck on the lower back, you will name the rigid body Hip instead.
Only either one of the Chest or the Hip rigid body is needed for the 6 rigid body skeleton.
Once the chest or hip rigid body has been created, the next step is to position and orient its pivot point at the appropriate location. You can use the Gizmo tool to easily translate the rigid body pivot points.
For the chest rigid body, the pivot point must be placed at the center of the torso, approximately at the heart center; which is in between the spine and the bottom end of the sternum. For the hip rigid body, the pivot point must be placed at the center of the hip bone.
After positioning the pivot point, adjust the orientation of the rigid body pivot also by using the rotate Gizmo tool. For creating 6 Rigid Body skeleton, the +z axis must direct towards the front of the actor.
Enabling the Orientation setting under the rigid body properties will reveal the orientation of the selected rigid body.
Now that the chest, or hip, rigid body has been set up, next step is to create a rigid body for the head. This can be either the active CV1 clip or an active puck attached to the head. Only one of them needs to be created.
To create the HMD rigid body, you can use the HMD tool in the Trackables pane to easily create a rigid body for the active CV1 clip. Make sure to choose either the +Z-forward or the +X-forward orientation when creating the rigid body, and the rigid body must be named HMDHead for +Z-forward orientation or HMDHeadX for +X-forward orientation.
The process of creating a head rigid body from an active puck is similar to the steps for creating the Chest rigid body. You can use the Trackables pane to define a rigid body named Head.
Once the rigid body is defined, use the Gizmo tool to translate the pivot point to at the center of the actor's head near the neck joint. Then, likewise, orient the rigid body so that +z axis is directing towards the front.
Now that the head and torso rigid body has been prepared, we can start defining the skeleton. Open the Trackables pane and select desired Rigid Body Skeleton from the marker set drop-down menu, and assign a name for the skeleton that will be created.
Ask the subject to strike a calibration pose (e.g. T-Pose). Then select the two rigid bodies and press Create on the Skeleton pane. This action will automatically define rigid bodies for the remaining active pucks on the hand/foot, and also place the pivot points at the proper location automatically. All of the rigid bodies will have the prefix with the name given to the skeleton (see screenshot below), and the skeleton will be created and tracked.
Rigid Body Names:
Step 1) Prepare 6 rigid bodies with markers.
Step 2) Attach rigid bodies at the following locations:
Step 3) Make sure the rigid bodies are securely attached.
First of all, define rigid body assets for all of the attached rigid bodies.
Name the rigid bodies with the following syntax:
Hip/Chest Rigid Body
VR: Using HMD for head tracking
Now you need to position the rigid body pivot points. Use the Gizmo tool and translate the rigid body pivot points so that each pivot point is located at its respective parent joint axis. Pivot point of the head rigid body must be placed over the head/neck joints, the hip rigid body must have its pivot point at the pelvis center, pivot point of the left/right hand rigid bodies must be placed over the wrist joints, and the left/right foot rigid bodies must have its pivot points over the ankle joints, as shown in the image below. If a Chest rigid body is used in place of the Hip rigid body, its pivot point location need to be plated at the heart center, solar plexus.
This is easier to set up by switching one of the cameras to a grayscale video mode and using the Reference View pane to monitor where the pivot point is placed within each respective joints.
VR: HMD Rigid Bodies
Orient the rigid body pivot points so that all of its z-axis is facing in forward-direction. This can be done easily using the Rigid Body pane. Ask the subject to face towards the positive-z direction (determined by the global coordinate system) and use the Edit tab on the Rigid Body pane to reset the orientations of the each rigid body. This will align the rigid body orientation with the global coordinate axis, making the z-axis direct forward.
Open the Skeleton pane and select the 6 Rigidbody Skeleton markerset. Name the skeleton that matches the prefix given to the rigid bodies.
Ask the subject to strike a calibration pose (e.g. T-Pose). Then select all six rigid bodies and press "Create" on the Skeleton pane. Created skeleton will search for rigid bodies with corresponding names for tracking. If all of the rigid bodies have been named correctly and the pivot points have been positioned and oriented properly, the skeleton will be tracked.