This wiki is intended for older versions of Motive. For the latest documentation, please refer to

Quick Start Guide: Precision Capture

Back to the Main PageBack to the Quick Start Guides List

With an optimized system setup, motion capture systems are capable of obtaining extremely accurate tracking data from a small to medium sized capture volume. This quick start guide covers setup instructions for precision capture and important cautions to keep in mind. This page also covers some of the precision verification methods in Motive. For more general instructions, please refer to the Quick Start Guide: Getting Started or corresponding workflow pages. Before going into details on precision tracking with an OptiTrack system, let's start with a brief explanation on the residual value, which is the key reconstruction output for monitoring the system precision.

Residual Value

The residual value is an average offset distance between the converging rays when reconstructing a marker; hence indicating preciseness of the reconstruction. The tolerable residual distance is defined from the Reconstruction pane. When one or more markers are selected in the Live mode or from a recorded 2D data, the corresponding mean residual value is displayed over the Status Bar located at the bottom of Motive. The residual values can also be displayed on the 3D viewport if Show Selected Residual is set to true in Application Settings. A smaller residual value means that the tracked rays converge more precisely and more accurate 3D reconstruction is achieved. A well-tracked marker will have a sub-millimeter average residual value.

MVQSG Residual1.png MVQSG Residual2.png

Capture Volume

First of all, optimize the capture volume for most precise and accurate tracking results. Avoid populated area when setting up the system and recording a capture. Clear any obstacles or trip hazards around the capture volume. Physical impacts on the setup will distort the calibration quality, and it could be critical especially when tracking at a sub-millimeter accuracy. Lastly, for best results, routinely recalibrate the capture volume.

Infrared Black Background Objects

Motion capture cameras detect reflected infrared light. Thus, having other reflective objects in the volume will alter the results negatively, which could be critical especially for precise tracking applications. If possible, have background objects that are IR black and non-reflective. Capturing in a dark background provides clear contrast between bright and dark pixels, which could be less distinguishable in a white background. The following images show a clear (left) and a less clear(right) image of a marker whose centroid calculation may have been compromised by an extraneous bright pixels from the background.

MVQSG IRBlack.png 295 px

Camera Placement

Cameras placed in a dome arrangement around a cubic meter volume.
Capturing multiple unique vantages measure more accurate positions on all of the coordinate axis

Optimized camera placement techniques will greatly improve the tracking result and the measurement accuracy. The following guide highlights important setup instructions for the small volume tracking. For more details on general system setup, read through the Hardware Setup pages.

Mounting Locations

For precise tracking, better results will be obtained by placing cameras closer to the target object (adjusting focus will be required) in a sphere or dome shaped camera arrangement, as shown in the images on the right. Good positional data in all dimensions (X, Y, and Z axis) will be attained only if there are cameras contributing to the calculation from a variety of different locations; each unique vantage adds additional data.

Mount Securely

For most accurate results, cameras should be perfectly stationary, securely fastened onto a truss system or an extremely rigid object. Any slight deformation or fluctuation to the mount structures may affect the result in sub-millimeter tracking applications. A small-sized truss system is ideal for the setup. Take extreme caution when mounting onto speed rails attached to a wall, because the building may fluctuate on hot days.

CameraMount Manfrotto.png Mount Clamp2.png

Focus and Aiming

FnA InFocus.png


Increase the f-stop higher (smaller aperture) to gain a larger depth of field. Increased depth of field will make greater portion of the capture volume in-focus and will make measurements more consistent throughout the volume.

Aim and Focus

Especially for close-up captures, camera aim and focus should be adjusted precisely. Aim the cameras towards the center of the capture volume. Optimize the camera focus by zooming into a marker in Motive, and rotating the focus knob on the camera until the smallest marker is captured with clearest image contrast.

For more information, please read through the Aiming and Focusing workflow page.

Motive Settings

The following sections cover key configuration settings which need to be optimized for the precision tracking.

Cameras Pane Settings

To open the cameras pane, click the camera icon on the main toolbar in Motive.

Setting Description
Gain Set the Gain setting to 1: Low (Short Range) for all cameras. Higher gain settings will amplify noise in the image.
Frame Rate Set the system frame rate (FPS) to its maximum value. If you wish to use slower frame rate, use the maximum frame rate during calibration and turn it down for the actual recording.
Threshold (THR) Do not bother changing the Threshold (THR) or LED values, keep them at their default THR = 200 and LED = 15. The Values EXP and LED are linked so change only the EXP setting for brighter images. If you turn the EXP higher than 250, make sure to wand extra slow to avoid blurred markers.
Exposure (EXP) For the precision capture, it is not always necessary to set the camera exposure to its lowest value. Instead, the exposure setting should be configured so that the reconstruction is most stable. Zoom into a marker and examine the jitters while changing the exposure setting, and use the exposure value that give the most stable reconstruction. Later sections will cover how to check the reconstruction and tracking quality. For now, set this number as low as possible while maintaining the tracking without losing the contrast of the reflections.

Optimizing Reconstruction Settings

To open the cameras pane click View > Reconstruction Settings on the command bar. Read through the Reconstruction page for details on each setting. For the precision tracking, important reconstruction settings and the appropriate values are listed below:

Setting Value Description
Residual (mm) <2.00 Set the allowable residual value smaller for the precision volume tracking. Any offset above 2.00 mm will be considered as inaccurate, and the corresponding 2D data will be excluded from reconstruction contribution.
Minimum Rays >= 3 Set the minimum required number of rays higher. More accurate reconstruction will be achieved when more rays converge within the allowable residual offset.
Minimum Thresholded Pixels >= 4 Since cameras are placed more close to the tracked markers, each marker will appear bigger in camera views. The minimum number of threshold pixels can be increased to filter out extraneous small reflections if needed.
Circularity >= 0.6 Increasing the circularity value will filter out non-marker reflections. Furthermore, it prevents collecting data from merged reflections where the calculated centroid is no longer reliable.


The following calibration instructions are specific to precision tracking. For more general information, refer to the Calibration page.


For calibrating small capture volumes for precision tracking, we recommend using a Micron Series wand, either the CWM-250 or CWM-125. These wands are made of invar alloy, very rigid and insensitive to temperature, and they are designed to provide a precise and constant reference dimension during calibration. At the bottom of the wand head, there is a label which shows a factory-calibrated wand length with a sub-millimeter accuracy. In the Calibration pane, select Micron Series under the OptiWand dropdown menu, and define the exact length under the Wand Length.

MVQSG Wandlabel.png MVQSG WandCalib.png

The CW-500 wand is designed for medium to large capture volumes, and it is not suited for calibrating small volumes. Not only it does not have indication on the factory-calibrated length, it is made with aluminum, which makes it more vulnerable to thermal expansions. During the wanding process, Motive references the wand length for calibrating the capture volume, and any distortions in the wand length would cause the calibrated capture volume to be scaled slightly differently, which can be significant when capturing precise measurements. For this reason, a micron series wand is suitable for precision tracking applications.

Note: Never touch the marker on the CWM-250 or CWM-125 since any changes can affect the calibration and overall data.

Precision Capture Calibration Tips

  • Wand slowly. Waving the wand around quickly at high exposure settings will blur the markers and distort the centroid calculations, at last, reducing the quality of your calibration.
  • Try not to occlude any of the calibration markers while wanding. Occluding markers will reduce the quality of the calibration.
  • A variety of unique samples is needed in order to achieve a good calibration. Wand in a three dimensional volume, wave the wand in a variety of orientations and throughout the volume.
  • Extra wanding in the target area you wish to capture will improve the tracking in the target region.
  • Wanding the edges of the volume helps improve the lens distortion calculations. This may cause Motive to report a slightly worse overall calibration report, but will provide better quality calibration; explained below.
  • Starting/stopping the calibration process with the wand in the volume may help avoid getting rouge samples outside your volume when entering and leaving.

Calibration Results

Calibration reports and analyzing the reported error is a complicated subject because the calibration can only use its own samples for validation. For example, sampling near the edge of the volume may improve the accuracy of the system but provide slightly worse calibration results. This is because the samples near the edge will have more errors to be corrected. Acceptable mean error varies based on your volume size, number of cameras, and desired accuracy. The key metrics to keep an eye on are the Mean 3D Error for the Overall Reprojection and the Wand Error. Generally, use calibrations with the Mean 3D Error less than 0.80 mm and the Wand Error less than 0.030 mm. These numbers may be hard to reproduce in regular volumes. Again, the acceptable numbers are subjective, but lower numbers are better in general.

Attention: Marker Placement

Two markers are placed too close to each other and their reflections are getting merged.

For close-up capture, it could be inevitable to place markers close to one another. When markers are placed in close vincinity, their reflections may be merged in camera’s imager. Merged reflections will have an inaccurate centroid locations, or they may even be completely discarded by the circularity filter or the intrusion detection feature. For best results, keep the circularity filter at higher setting (>0.6) and decrease the intrusion band in Reconstruction settings to make sure only relevant reflections are reconstructed. The optimal balance will depend on the number and arrangement of the cameras in the setup.

There are editing methods to discard or modify the missing data. However, for most reliable results, such marker intrusions should be prevented before the capture by separating the marker placements or by optimizing the camera placements.

Attention: Temperature

Temperature of the processor board and the ringlight board displayed in the camera info.

In a mocap system, camera mount structures and other hardware components may be affected by temperature fluctuations. Refer to linear thermal expansion coefficient tables to examine which materials are susceptible to temperature changes. Avoid using a temperature sensitive material for mounting the cameras. For example, aluminum has relatively high thermal expansion coefficient, and therefore, mounting cameras onto aluminum mounting structures may distort the calibration quality. For best accuracy, routinely recalibrate the capture volume, and take the temperature fluctuation into an account both when selecting the mount structures and before collecting data.

Ambient Temperature

An ideal method of avoiding influence from environmental temperature is to install the system in a temperature controlled volume. If such option is unavailable, routinely calibrate the volume before capture, and recalibrate the volume in between sessions when capturing for a long period of time. The effects are especially noticeable on hot days and will significantly affect your results. Thus, consistently monitor the average residual value and how well your rays converge to individual markers.

Camera Heat

The cameras will heat up with extended use, and change in internal hardware temperature may also affect the capture data. For this reason, avoid capturing and/or calibrating right after powering the system. Tests have found that the cameras need to be warmed up in Live mode for about an hour until it reaches a stable temperature. For Ethernet camera models, camera temperatures can be monitored from the Camera Preview (2D) pane in Motive (Camera Preview (2D) pane > Eye Icon > Camera Info).

Attention: Vibrations

Especially for measuring at sub-millimeters, even a minimal shift of the setup can affect the recordings. Re-calibrate the capture volume if your average residual values start to deviate. In particular, watch out for the following:

  • Avoid touching the truss or mounting device for the cameras.
  • Keep the capture area away from heavy foot traffic. People shouldn't be walking around the volume while capture is taking place.
  • Closing doors, even from the outside, may be noticeable during recording.

Reconstruction Verification

The following methods can be used to check the tracking accuracy and to better optimize the reconstructions settings in Motive.

Verification Method 1

First, go into the perspective view pane > select a marker, then go to the Camera Preview pane > Eye Button Viewport16.png > Set Marker Centroids: True. Make sure the cameras are in the object mode, then zoom into the selected marker in the 2D view. The marker will have two crosshairs on it; one white and one yellow. The amount of offset between the crosshairs will give you an idea of how closely the calculated 2D centroid location (white) aligns with the reconstructed position (yellow). Switching between the grayscale mode and the object mode will make the errors more distinguishable. The below image is an example of a poor calibration. A good calibration should have the yellow and white lines closely aligning over each other.

MVQSG Optimization1.png

Verification Method 2

The calibration quality can also be analyzed through checking the convergence of the tracked rays into a marker. This is not as precise as the first method, but the tracked rays can be used to check calibration quality of multiple cameras at once. First of all, make sure tracked rays are visible; Perspective View pane > Eye button > Tracked Rays. Then, select a marker in the perspective view pane. Zoom all the way into the marker (you may need to zoom into the sphere), and you will be able to see the tracking rays (green) converging into the center of the marker. A good calibration should have all the rays converging into approximately one point, as shown in the following image. Essentially, this is a visual way of examining the average residual offset of the converging rays.

MVQSG Optimization2.png