Back to the Main Page
When a motion capture system is used in conjunction with force plates, they work together as a powerful tool for various research applications including biomechanical analysis, clinical gait analysis, physiology research, sports performance research, and much more. An OptiTrack motion capture system can synchronize with force plates to obtain both kinematic and kinetic measurements. Force plate integration is supported only with a Prime camera system using the eSync synchronization hub. For Bertec force plate integration support, you must use Motive 1.10 or above. This page provides guidelines for setting up and configuring Bertec force plates — with digital outputs — along with the OptiTrack motion capture system.
For detailed information on specifications and configurations on the force plates, refer to the documentation provided by the force plate manufacturer.
In order to integrate force plate systems with Motive, you will need to setup the required drivers and plugins. Motive installer is packaged with the Peripheral Device module which can be added during the Motive installation process. This module includes all necessary drivers and plugins for integrating external devices including force plates (AMTI and Bertec) in Motive. During the Motive installation, a list of program features will be shown in the Custom Setup section. Here, change the setting for the Peripheral Device module, as shown in the below image, so that the module is installed along with Motive Files.
Note : Even if you are not using NI-DAQ, it is still necessary to install NI-DAQmx drivers that come up next in the installer.
Note: You cannot run Digital Acquire and Motive together and have them connected to the plate(s) at the same time.
Tip: To double check that the dimensions are modified properly, you can place extra retroreflective markers on each corner of the platform and monitor the coincidence of the markers position with the force plate assets from the perspective view.
Note: Zeroed scales of Bertec force plates are saved within their software driver, and each time the driver restarts, these settings are refreshed. This means that the force plate zero setting will be refreshed each time you start Motive, or each time the device is disabled and enabled back again in Motive. Please be aware of this behavior and zero your plates when necessary. In Motive, there is a Zero On Enable property setting for Bertec force plates under the Devices pane, and enabling this setting will automatically zero your plate each time the device is enabled or when Motive restarts. The Zero On Enable setting is enabled by default.
When synchronizing through the eSync, use the following steps for configuring the sync settings in Motive. This will allow both systems to be simultaneously triggered with reference to the master synchronization device. The Recording Gate signal must be sent out from the eSync and inputted into the Bertec force plate system for synchronization.
IMPORTANT NOTE: For this synchronization setup to work properly, the Bertec amplifier firmware must be updated to its most recent version (above June 2016 release). Contact Bertec for instructions on updating the firmware.
Before you start recording, you may want to validate that the camera and force plate data are in sync. There are some tests you can do to examine this.
The first method is to record dropping a retroreflective ball/marker onto the platform few times. The bouncing ball produces a sharp transition when it hits the surface of the platform, and it makes the data more obvious for validating the synchronization. Alternately, you can attach a marker on a tip of the foot and step on and off the force plate. Make sure that your toe — closest to the marker — strikes the platform first, otherwise the data will seem off even when it is not. You can then monitor the precise timing of the ball or the foot impacting the force plate and compare them between the mocap data and the force plate data. ↑
The following is an example of validating both good and bad synchronizations using these methods:
Above configurations set the sync chain to be in Free Run Mode. This means that the recording of both the mocap system and the force plate system are triggered simultaneously at the same time and each system runs at its own rate.
Two systems, however, are synchronized at the trigger point but not at every frame. For this reason, alignment of the mocap data and the force plate data may gradually drift from each other for longer captures. But this is not a problem since the sync chain will always be re-synchronized each time recording in Motive is triggered. Furthermore, Takes in general do not last too long for this drift to take effect on the data.
However, this could be an issue when live-streaming the data since recording is never initiated and two systems will be synchronized only when Motive first launches. To zero out the drift, the ReSynch feature can be used. Right-click on force plates from either the Devices pane or the perspective view, and select Resynch from the context menu to realign the sampling timing of both systems.
First of all, it is important to note that without a master synchronization device, recording for the camera system and the force plates will not be triggered exactly at the same time. If you want your system to be timed perfectly, we recommend synchronizing through the eSync 2.
If you are using an Ethernet system without an eSync, ignore the synchronization configuration options. From the Devices pane, make sure that that the force plate sampling rate is a multiple of the tracking frames per second (e.g. 100 Hz and 1000 Hz). Motive will alert you if the sampling rates of cameras and force plates disagree. When the force plate sampling rate is not set to an integer multiple of the camera frame rate, force plate data may record improperly and cause an error.
Note: Bertec digital force plates can collect data up to a maximum of 1000 Hz sampling rate.
Force plate data can be monitored from the Graph View pane. You will need to configure a custom graph layouts to show force plate data. As shown in the images, make sure the desired force plate data channels (Fx, Fy, Fz, Mx, My, or Mz) are selected to be plotted. Then, when you select a force plate in Motive, and the data from the corresponding channels will be plotted on the graphs. When both reconstructed markers and force plate channels are selected, the force plot will be sub-sampled in order to be plotted along with trajectory data. For more information about how to configure graph layouts, read through the Graph View pane page.
We recommend the following programs for analyzing exported data in biomechanics applications:
Since Motive uses a different coordinate system than the system used in common biomechanics applications, it is necessary to modify the coordinate axis to a compatible convention in the C3D exporter settings. For biomechanics applications using z-up right-handed convention (e.g. Visual3D), the following changes must be made under the custom axis.
This will convert the coordinate axis of the exported data so that the x-axis represents the anteroposterior axis (left/right), the y-axis represents the mediolateral axis (front/back), and the z-axis represents the longitudinal axis (up/down).